2-inch leveling kit
+2.50°caster above factory
2005–2022 Ford F-250/F-350 Super Duty Radius Arm Drop Brackets | 2–3 Inch Lift
Correct Radius Arm Angle on Your Leveled Super Duty
APOC Industries radius arm drop brackets fit 2005–2022 Ford F-250 and F-350 Super Duty 4WD trucks with 2–3 inch leveling kits or suspension lifts, including gas and diesel models. This driver- and passenger-side set lowers the rear radius arm mounting points at the frame, allowing you to keep your existing radius arms while correcting their angle.
How These Brackets Help
Raising the front changes radius arm geometry and can reduce caster. These brackets add positive caster and help move the front axle forward toward its factory position, addressing steering wander associated with lift-induced caster loss. They are not a substitute for diagnosing worn steering or suspension components.
Expected Caster Gain Above Factory
Leveling the truck reduces caster as lift height increases. With the APOC radius arm drop brackets installed, the following figures represent the expected net caster gain above the truck's original factory-height caster at each listed leveling height. They account for the caster lost from leveling; they are not gains to add to an already-leveled truck's caster reading.
- 2-inch leveling kit: +2.50° above factory caster.
- 2.5-inch leveling kit: +1.67° above factory caster.
- 3-inch leveling kit: +0.85° above factory caster.
Example: If your truck's original factory-height caster is 3.00°, the expected caster with the leveling kit and these drop brackets installed would be 5.50° at 2 inches, 4.67° at 2.5 inches, or 3.85° at 3 inches. The 3.00° starting point is an example, not a stated Ford factory specification.
These figures are expected gains, not guaranteed final alignment readings. Have the final caster checked during front-end alignment after installation.
Construction & Features
- Laser-cut 1/4" steel plate construction.
- Powder-coated finish.
- Relocates the frame-side radius arm pivot downward.
- Helps restore axle position and adds positive caster on compatible 2–3 inch lifted setups.
- Uses the existing factory frame-bracket holes.
- Made in the USA by APOC Industries.
What's Included
- (2) radius arm drop brackets: driver side and passenger side.
- (4) new 3/4" mounting bolts, two per side.
- Installation instructions.
The factory radius arm pivot bolts are retained and reused to attach the radius arms in the lower bracket holes.
Fitment
- 2005–2022 Ford F-250 Super Duty 4WD.
- 2005–2022 Ford F-350 Super Duty 4WD.
- Gas and diesel models.
- For 2–3 inch leveling kits or suspension lifts only. Do not use outside this range.
Installation & Clearance Notes
The brackets nest inside the factory radius arm frame brackets and use the existing mounting holes. In some cases, the uppermost forward factory hole may require light reaming to accept the supplied 3/4" bolt. Remove only the minimum material needed for a snug fit; do not enlarge the hole beyond the guide's instructions.
Both frame-side radius arm pivot bolts must be removed as described in the guide so the axle and arms can move together. Follow the complete support, installation, and torque procedures before beginning work.
- Tools include appropriate vehicle-support equipment, sockets, a torque wrench, and potentially a reamer or round file.
- Check clearance through suspension travel and have front-end alignment checked after suspension work.
- Recheck fastener torque after 50–100 miles and inspect hardware during routine service.
Further Reading
Expected Caster Gain Above Factory
2.5-inch leveling kit
+1.67°caster above factory
3-inch leveling kit
+0.85°caster above factory
These are expected net gains above the truck's original factory-height caster with both the leveling kit and APOC drop brackets installed. They already account for caster lost from leveling. Do not add these figures to an already-leveled truck's caster measurement.
Illustrative example
Starting with 3.00° original factory-height caster gives expected final caster of 5.50° with a 2-inch kit, 4.67° with a 2.5-inch kit, and 3.85° with a 3-inch kit. 3.00° is an example, not a universal Ford factory specification.
Final caster readings must be checked during front-end alignment and are not guaranteed.
Built Right. Backed Right.
Our crew’s on call Monday–Friday, 9–5 EST. Hit us up at 865-983-5004 — real support, done right.
FAQ
Use this text to share information about your product or shipping policies.
Does this bracket improve caster angle?
Yes — one of the primary benefits of the APOC radius arm drop bracket is caster correction. When you lift a Ford F-250/350, the radius arms pull the axle rearward, reducing your caster angle. Low caster causes poor returnability, wandering on the highway, and unstable handling. This bracket restores proper caster geometry so your truck tracks straight and handles confidently at any speed.
How much caster does this bracket restore?
The APOC radius arm drop bracket is engineered to fully restore factory caster specs for 2–4" lift heights — and then some. You'll actually end up with slightly more positive caster than stock, which means better straight-line stability, improved steering returnability, and a more confident feel on the highway.
What are the symptoms of incorrect caster on a lifted truck?
Common symptoms include the steering wheel not returning to center after turns, the truck pulling to one side, highway wander, and increased steering effort. If you're experiencing these after a lift, caster correction is likely the fix.
Our customer support is available Monday to Friday: 8am-8:30pm.Average answer time: 24h
Radius Arm Drop Bracket
Engineered suspension geometry — done right
Caster Correction Built In
Most lift kits leave your caster angle short. Our drop bracket restores factory caster — plus a little extra — for confident straight-line tracking and crisp steering returnability right out of the box.
Built for 2–4" Lift Heights
Engineered specifically for the 2–4" lift range on solid front axle Ram trucks. Correct geometry, proper pinion angle, and zero driveline vibration — exactly what your build needs.
Bolt-On. No Cutting Required.
Designed to use existing factory mounting points on your Ford Super Duty F-250/350. No drilling, no cutting, no fabrication — just a clean, reversible install that goes in with basic hand tools.
Customer Reviews
Overall rating: 5.0 / 5 from 7 reviews.
Installed in my drive in about 45 minutes . Good solid built product that installed easily if you have some mechanical ability. Took care of my steering issues I had from a 2 1/2 inch lift.
2017-2022 Ford F-250/F-350 Super Duty Radius Arm Drop Bracket by Apoc Industries | 2"-4" Lift
Definitely good quality, and built pretty solid. Readjusted the camber on the front axle for sure and was very easy install. Go easy on the torque as you can start to bend the support brackets built in.
2017-2022 Ford F-250/F-350 Super Duty Radius Arm Drop Bracket by Apoc Industries | 2"-4" Lift
If your running a leveling kit you definitely need these drop brackets, corrects the floating steering feel and tightens it up, rides and drives much better getting the Caster back were its supposed to be.
2017-2022 Ford F-250/F-350 Super Duty Radius Arm Drop Bracket by Apoc Industries | 2"-4" Lift
Couldn’t have asked better for the price , very solid company with very solid products . Would highly recommend!
2017-2022 Ford F-250/F-350 Super Duty Radius Arm Drop Bracket by Apoc Industries | 2"-4" Lift
Went in perfectly!!!
2017-2022 Ford F-250/F-350 Super Duty Radius Arm Drop Bracket by Apoc Industries | 2"-4" Lift
WORKED GREAT
2017-2022 Ford F-250/F-350 Super Duty Radius Arm Drop Bracket by Apoc Industries | 2"-4" Lift
I had to grind the top of the brackets where they meet up to the frame alittle cause the bolt holes weren’t lining up. After that everything went smoothly. Still recommend them.
2017-2022 Ford F-250/F-350 Super Duty Radius Arm Drop Bracket by Apoc Industries | 2"-4" Lift
Learn how to get the most out of your lift with expert install guides and geometry tips from Apoc Industries.
Suspension Tech & Guides
geometry correction
Radius Arm Drop Brackets: What They Are and Why Your Lifted Truck Needs Them
Learn how radius arm drop brackets restore proper suspension geometry on lifted trucks, correcting caster loss, bump steer, and ride quality issues.
Technical Resources
Caster Setup Guide
Everything you need to know about caster angle on lifted straight axle trucks — what it is, how to measure it, and how to set it correctly.
4-link
What is Caster? A Complete Guide for Lifted Straight Axle Trucks
A deep-dive technical guide explaining caster angle for lifted straight axle trucks — what it is, why it matters, how to measure it, and how to set it correctly with adjustable radius arms or 4-lin...