


1998–2009 Ford Ranger 1.5"–2" Rear Lift Shackles
Bring Your Ranger’s Rear Stance Up.
Raise the rear of your 1998–2009 Ford Ranger with APOC rear lift shackles offering 1.5–2 inches of lift. Designed for a rear suspension height increase, these shackles are a lift application, not a rear lowering kit.
When your build calls for more rear ride height, start with components matched to your Ranger’s year range and your overall suspension plan. These lift shackles target the rear of the truck, helping you work toward the stance you want without describing a rear-only component as a complete front-and-rear lift kit.
1998–2009 Ford Ranger Lift Shackle Details
- Vehicle application: 1998–2009 Ford Ranger.
- Suspension location: Rear.
- Lift height: 1.5–2 inches.
- Component type: Rear suspension lift shackles.
Plan the Stance You Want
Consider your Ranger’s current front-to-rear height before choosing a rear lift. Raising the rear changes the truck’s stance; it does not automatically create a level profile. Plan around any existing front or rear suspension modifications rather than assuming separate lift components will produce a specific final height when combined.
Actual ride-height change can vary with the existing suspension setup, leaf-spring condition and vehicle load. A suspension lift should not be treated as a repair for worn springs or as an increase in the truck’s rated payload or towing capacity.
Check Your Application Before Ordering
Confirm your Ranger’s model year and suspension configuration before ordering. For a truck with existing lift components or other rear suspension changes, contact APOC to discuss your setup and application-specific installation requirements.
Ready for a taller rear stance? Build your 1998–2009 Ford Ranger’s suspension plan around these 1.5–2-inch rear lift shackles.

Built Right. Backed Right.
Our crew’s on call Monday–Friday, 9–5 EST. Hit us up at 865-983-5004 — real support, done right.
Product Specifications
Before/after
Showcase your product benefit by using before/after image comparison.

Before

After
Ford Lowering Shackles
Built for Your Ford
What's Included :
Apoc 2" Rear Lowering Shackle Kit (Ford F-150)
Everything you need for a clean, reliable install:
- (2) Heavy-Duty 2” Rear Lowering Shackles (Driver + Passenger side)
- Pre-installed Polyurethane Bushings
- Pre-installed Steel Inner Sleeves
- (1) Replacement Bolt for Rear Leaf Spring (for frame clearance applications)
- Installation Instructions (Printed or Digital PDF)
Note: Factory hardware is reused except for the included replacement rear bolt. No other bolts or nuts are necessary for proper install.
Note: Factory hardware is reused except for the included replacement rear bolt. No other bolts or nuts are necessary for proper install.
Premium Bushings – Built for Life:
Apoc Premium Polyurethane Bushings
Backed by a Lifetime Warranty, Apoc Premium Polyurethane Bushings are built to outlast and outperform—delivering long-term reliability, quiet operation, and zero-compromise performance in every shackle kit we build.
Our premium bushings are crafted from high-density polyurethane to outperform standard rubber in every category:
- Resists cracking, shrinking, and dry rot – holds up in all climates and under load
- Low-deflection design – improves suspension responsiveness without harshness
- Noise-free fit – precision-molded for a tight, rattle-free connection
- Grease-retaining channels – accepts PTFE-based bushing grease for smooth, long-term articulation
Like all Apoc components, our bushings are built for abuse but refined for street use—giving you a durable, quiet, and dependable ride whether you're hauling, cruising, or cornering.
Important Installation Fitment Note:
Clearance Note – Rear Bed Support Trimming
- Rear bed support trimming is required for proper shackle clearance on some models.
- Contact may occur only at full suspension drop, such as when the vehicle is lifted off the ground for service.
- At normal ride height, the shackle remains clear and does not interfere with the bed support.


Crafted Without Compromise
100%
Red, White & Built Right
Lifetime Warranty Polyurethane Bushings
Built to Last, Easy to Rebuild
Apoc Industries' high-performance polyurethane bushings are backed by a lifetime warranty and engineered for durability you can count on. Easily rebuildable with basic tools, they deliver a firm, responsive ride without the hassle—made for daily drivers and built for the long haul.

Before

After
FAQ'S
Ford Lowering Shackles
Our customer support is available Monday to Friday: 9am-5pm EST. 865-983-5004
Do Lowering Shackles Affect Ride Quality?
In most cases: No, not significantly.
Lowering shackles drop the rear of the truck by relocating the rear leaf spring mounting point—not by removing leaf springs or altering spring rates. This means the suspension system continues to function much like stock.
✅ Why Ride Quality Usually Stays the Same
- Leaf Spring Geometry Is Preserved: The springs still carry the load the same way—they’re just mounted higher relative to the frame.
- No Change to Spring Rate or Shocks: Since you’re not swapping springs or shocks (for mild drops), the ride feel remains largely OEM.
- Polyurethane Bushings: Help maintain quiet operation and reduce flex, improving long-term ride consistency.
⚠️ Situations Where Ride May Be Affected
🔸 Reduced Suspension Travel: A 2" drop brings the axle closer to the frame. If bump stops aren't adjusted, you may hit them sooner over large bumps.
🔸 Increased Axle Angle or Leaf Spring Arching: Rare, but possible if combined with other drop components or a flip kit.
🔸 Towing and Hauling: With less rake, trucks may appear to sag more under load. Suspension upgrades like helper bags may be needed for heavy-duty use.
💬 Summary
For 1"–2" lowering shackles, ride comfort remains nearly identical to factory, making them one of the easiest and cleanest ways to drop the rear of your truck without compromising everyday drivability.
⏱️ Installation Time for Lowering Shackles
For most vehicles—including the 2004–2014 Ford F-150—installing rear lowering shackles typically takes:
🕒 Estimated Install Time: 1 to 1.5 hours
🔧 Install Overview
- Skill Level: Beginner to moderate (depending on experience with suspension work)
- Tools Needed:
- No cutting, welding, or fabrication is required. This is a bolt-on installation using factory mounting points.
- Most installs are done with basic hand tools in a home garage.
💡 Pro Tips
- Loosen leaf spring bolts with the truck on the ground before lifting for easier access.
- Use a pry bar or lift the axle slightly to relieve tension when aligning the new shackles.
- Always torque bolts to factory specs once the vehicle is back on the ground under full weight.
Can I Use Factory Hardware?
Yes — most 2004–2014 F-150s can reuse factory bolts. On some trucks, one bolt per side may need to be cut due to frame clearance. However, many have successfully removed the bolt without cutting.
A replacement bolt is included.
Replace hardware if rusted, damaged, or upgrading finishes.
Always torque at ride height for proper bushing preload.
🛢️ What Type of Grease Should I Use in Polyurethane Bushings?
Using the correct grease is essential for maintaining quiet, smooth operation and extending the life of polyurethane bushings—especially in suspension components like lowering shackles.
✅ Recommended Grease: Synthetic Waterproof Grease with PTFE (Teflon)
This type of grease is specifically designed for polyurethane bushings. It creates a slick barrier between the bushing and sleeve, preventing noise, binding, and premature wear.
🔧 Key Features to Look For:
- 🟩 PTFE-Based or Silicone-Based – Both are bushing-safe and reduce friction
- 🟩 Waterproof & Non-Petroleum – Resists washout and won’t degrade polyurethane
- 🟩 Thick, Tacky Formula – Stays in place during articulation and suspension travel
- 🟩 Non-Reactive – Safe for all types of polyurethane and metal sleeves
⚠️ Avoid These:
- ❌ Petroleum-Based Grease (like standard lithium or chassis grease) – Can cause polyurethane to soften, swell, or degrade over time
- ❌ WD-40 or Spray Lubricants – Not a true lubricant and quickly evaporates
💡 Pro Tip
Apply a generous coat of grease inside the bushing bore and on the sleeve during installation. If your shackles include zerk (grease) fittings, pump fresh PTFE grease in every 6–12 months for best performance.
